Slew Rate of DAC4800A and Cherry

The DAC4800A and Cherry amplifiers are "switching amps", so technically, the internal slew rate is that of the output stage (about 7200V/uS). The output filter of the amp removes the switching wave and yields an output slew rate of about 20V/uS (with an 8 ohm load). This is a respectable number, but keep in mind that it is limited by the output filter and increases as load impedance goes down.

The frequency response goes up to 60KHz on the DAC4800A and Cherry amps. This is a more valuable number than slew rate to many.

The sound of these amps can't be summed up with measurements (even though they are excellent) since they are designed from the ground up to deliver the best in music reproduction, not just test results in a lab.

Line Conditioners?

The DAC4800A and Cherry are designed to tolerate large AC mains fluctuations so you shouldn't need any line conditioning (save some money there). In fact, these amps even tolerate brief brown outs, playing through them without any noticeable effect.

About Speaker Cables --- They Don't Need to Cost a Fortune!

It comes down to resistance and inductance. If you can solder, buy 12 gauge or 14 gauge (if the run length is less than 15 feet) wire and get terminations from Digi-Key. By terminations, I mean banana plugs or spade lugs. I definitely recommend soldered connections instead of crimped for long life. I agree that this is a typical area for spending too much when it really doesn't make a difference to the sound or your system. This comes from an engineer with 20 years experience, not a marketing firm.

Audio Review Still Hasn't Responded

We tried to add the DAC4800A amplifier (see http://www.digitalamp.com/4800a_amp1.htm) to Audio Review so we can get customers to add reviews there. However, there is no selection for adding a new manufacturer. The listing shows up with "unknown" as the manufacturer. Here's the link:
http://www.audioreview.com/cat/amplification/amplifiers/unknown/dac4800a/PRD_419903_1583crx.aspx

We wrote to them, but no reply. We posted to the help board, but the post was removed.

Does anyone know somebody in charge at Audio Review? We would like to get on the manufacturers list. Locking us out is just not fair. Thanks.

Why Our Amps Sound Better

Some of our customers have told us that they love the sound of our digital (technically "Class-D") amps, but they don't like the sound of other digital amps (from other companies). It might be the output filter or feedback design. People often criticize me for saying that feedback wrapped around the output filter of a Class-D amp can have a negative impact on the sound. Actually, this could be your answer!

By the way, fake class designations like "Class-T" or "Class-Z" are actually Class-D. The definition of "Class-D amplifier" is "an amplifier that uses its output devices as switches". This is a pet peeve of mine.

Thanks for hearing me out.

Switching Amplifier Output Ripple Doesn't "Fold Down"

Regarding "folding down", this is called aliasing and is explained by sampling theory. Here is a basic explanation:
http://en.wikipedia.org/wiki/Nyquist%E2%80%93Shannon_sampling_theorem#Aliasing

Aliasing only happens when the waveform is sampled, which is not the case for a switching amplifier output driving a loudspeaker. The time domain output waveform of a switching amplifier (after the output filter) has switching ripple superimposed on top of the audio. The ripple is ultrasonic, so it is not heard. The mechanical limitations of loudspeakers do not allow this superimposed waveform to enter the room, not that it would matter anyway, as long as the switching frequency (Fsw) is high enough (>100KHz). Most switching amps change states (switch) at a rate of 350KHz or greater. Higher switching rates cause additional EMI and lower efficiency, and lower rates are harder to filter. The power dissipated in the loudspeaker by the ripple is typically a few milliwatts.

In order to accurately measure the performance of a switching amplifier, a filter that removes most of the ripple is usually placed between the amplifier under test and the measurement device. Such a filter requires flat response out to 20KHz or greater, but a rapid fall-off by the 100KHz range. Attempting to measure a switching amplifier without such a filter can drive the measurement equipment nuts as it tries to sync to the amplifier's output ripple instead of the audio signal.

Links to DAC4800A and Cherry Amplifier Information

Here's a link to the DAC4800A page:
http://www.DigitalAmp.com/4800a_amp1.htm

Here's a link to the Cherry page:
http://www.DigitalAmp.com/Cherry_amp2.htm

Here are links to reviews:
http://www.DigitalAmp.com/DAC_REVIEWS.htm
http://www.TrueDigitalPower.com/ (Amazon)
http://www.TrueDigitalAmp.com/ (Amazon)